R2hobbies.com Eurgle Spécifications télécharger pdf

80A Brushless Speed Controller

INSTRUCTIONS

Warnings

· We strongly recommend to calibrate the throttle range of transmitter when you first use the controller or

when using a new/different transmitter or receiver.

·When connecting the ESC to battery pack, please ensure the polarity is correct. Incorrect polarity may cause

permanent damage to the ESC and such damage is not covered by manufacturer’s WARRANTY.

·When you use the ESC, turn on the transmitter BEFORE powering on the receiver.

·When you finish the flying, power off the receiver BEFORE turning off the transmitter.

·The limiting current is set to the ‘standard mode’ in factory. It is suitable for use in most configurations.

Only experienced technicians can adjust this programming.

·In Governor Mode, the brake is always disabled and the soft cutoff is always active.

·Changing the PWM may cause the motor to heat ahead of time.

·Never disconnect the battery pack while the motor is running, as this could cause damage to the speed con-

troller and/or motor.

·Connectors with low conductivity may cause erratic motor rotations or other unexpected

movements.

·If you do not use the BEC function of the ESC and are using a separate receiver pack or UBEC to power

receiver and servos instead, please disconnect the red wire from the ESC’s receiver lead.

·Due to adopt advanced switching BEC technology, the switching frequency of the on-board BEC may make

some disturbance to receiver when use with some of 35Mhz transmitters and receivers, (such as Multiplex

35Mhz transmitter and receiver). We strongly recommend to disconnect the red wire from the ESC’s receiver

lead and use a separate receiver battery to power the receiver and servos when use with some of 35Mhz trans-

mitter and receiver.

·The controller will automatically power off the motor if the battery voltage drops below the programmed

cut-off voltage (factory preset at 6.0V). Try using a smaller prop on the motor, or using batteries with a higher

rating. It is especially important for the user of Li-poly cells.

·Allowing water, lubricants, moisture or other foreign objects inside the ESC will VOID the WARRANTY.

Exposure to CA glue or its fumes can cause damage and malfunctions; this will also VOID the WARRANTY.

1 2 3 4 5 6 ... 13 14

Résumé du contenu

Page 1 - INSTRUCTIONS

80A Brushless Speed Controller INSTRUCTIONS Warnings · We strongly recommend to calibrate the throttle range of transmitter when you first use t

Page 2

Eurgle ESC-80A

Page 3 - Ⅵ Using the ESC

Eurgle ESC-80A

Page 4 - Ⅶ Installing Eurgle Software

Appendix Eurgle ESC s offer eight user programmable features, including low cutoff voltage, current limiting, brake type, timing advance, cutoff type

Page 5

· Timing Advance · Cutoff Type NOTE: Soft cutoff is always automatically active in Governor Mode. ·Start Type · Governor Mo

Page 6 - Ⅸ Using the software

· PWM Switching Rate Note: we strongly recommend only the experienced modeler could change this setting. Ⅹ All models of Eurgle controllers

Page 7

Eurgle ESC-80A MANU

Page 8

Page 9

Eurgle E

Page 10

Page 11 - · Diary panel

Eurgle

Page 12 - Appendix

Eurgle

Page 13

Eurgl

Page 14

Eurgle E

Plus de documents pour Télécommandes R2hobbies.com Eurgle

Voir le document R2hobbies.com Eurgle Spécifications

R2hobbies.com Eurgle Spécifications (14 pages)

Voir le document R2hobbies.com Eurgle Manuel d'instructions

R2hobbies.com Eurgle Manuel d'instructions (18 pages)

Commentaires sur ces manuels

Pas de commentaire

R2hobbies.com Eurgle Spécifications

Naviguer en ligne ou télécharger Spécifications pour Télécommandes R2hobbies.com Eurgle. R2hobbies.com Eurgle Specifications Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Télécommandes R2hobbies.com Eurgle

Commentaires sur ces manuels

Produits connexes et manuels pour Télécommandes R2hobbies.com Eurgle